AES3 (also known as AES/EBU) is a standard for the exchange of digital audio signals between professional audio devices. An AES3 signal can carry two channels of PCM audio over several transmission media including balanced lines, unbalanced lines, and optical fiber.^[1]

AES3 was jointly developed by the Audio Engineering Society (AES) and the European Broadcasting Union (EBU). The standard was first published in 1985 and was revised in 1992 and 2003. AES3 has been incorporated into the International Electrotechnical Commission's standard IEC 60958, and is available in a consumer-grade variant known as S/PDIF.

History and development[edit]

The development of standards for digital audio interconnect for both professional and domestic audio equipment, began in the late 1970s^[2] in a joint effort between the Audio Engineering Society and the European Broadcasting Union, and culminated in the publishing of AES3 in 1985. The AES3 standard has been revised in 1992 and 2003 and is published in AES and EBU versions.^[1] Early on, the standard was frequently known as AES/EBU.

Variants using different physical connections are specified in IEC 60958. These are essentially consumer versions of AES3 for use within the domestic high fidelity environment using connectors more commonly found in the consumer market. These variants are commonly known as S/PDIF.

Hardware connections[edit]

The AES3 standard parallels part 4 of the international standard IEC 60958. Of the physical interconnection types defined by IEC 60958, three are in common use.

IEC 60958 Type I—Balanced, XLR[edit]

XLR connectors, used for IEC 60958 Type I connections.

Type I connections use balanced, 3-conductor, 110-ohm twisted pair cabling with XLR connectors. Type I connections are most often used in professional installations and are considered the standard connector for AES3. The hardware interface is usually implemented using RS-422 line drivers and receivers.

IEC 60958 Type II—Unbalanced, RCA[edit]

Orange RCA connector, used for IEC 60958 Type II connections.

Type II connections use unbalanced, 2-conductor, 75-ohm coaxial cable with RCA connectors. Type II connections are used most often in consumer audio installations and are often called coaxial S/PDIF connections.

IEC 60958 Type III Optical—Fiber, F05/TOSLINK[edit]

F05/TOSLINK connector, used for IEC 60958 Type III connections.

Type III Optical connections use optical fiber—usually plastic, but occasionally glass—with F05 connectors, which are more commonly known by their Toshiba brand name, TOSLINK. Like Type II, Type III Optical connections are also used in consumer audio installations and are often called optical S/PDIF connections.

Other connections[edit]

BNC connector, used for AES-3id connections.

The AES-3id standard defines a 75-ohm BNC electrical variant of AES3. This uses the same cabling, patching and infrastructure as analogue or digital video, and is thus common in the broadcast industry.

AES3 digital audio format can also be carried over an Asynchronous Transfer Mode network. The standard for packing AES3 frames into ATM cells is AES47.

For information on the synchronization of digital audio structures, see the AES11 standard. The ability to insert unique identifiers into an AES3 bit stream is covered by the AES52 standard.

Relation to S/PDIF[edit]

The precursor of the IEC 60958 Type II specification was the Sony/Philips Digital Interface, or S/PDIF. S/PDIF and AES3 are similar in many ways and are interchangeable at the protocol level, but at the physical level they specify different electrical signaling levels and impedances, which may be significant in some applications.

Protocol[edit]

Simple representation of the protocol for both AES3 and S/PDIF

The low-level protocol for data transmission in AES3 and S/PDIF is largely identical, and the following discussion applies for S/PDIF, except as noted.

AES3 was designed primarily to support stereo PCM encoded audio in either DAT format at 48 kHz or CD format at 44.1 kHz. No attempt was made to use a carrier able to support both rates; instead, AES3 allows the data to be run at any rate, and encoding the clock and the data together using biphase mark code (BMC).

Each bit occupies one time slot.

Each audio sample (of up to 24 bits) is combined with four flag bits and a synchronisation preamble which is four time slots long to make a subframe of 32 time slots.

Two subframes (A and B, normally used for left and right audio channels) make a frame. Frames contain 64 time slots and are produced once per sample time. This determines the clock rate.

At the highest level, each 192 consecutive frames are grouped into an audio block. While samples repeat each frame time, metadata is only transmitted once per audio block.

At the default 48 kHz frame rate, there are 250 audio blocks per second, and 3,072 kilobits per second with a biphase clock of 6.144 MHz ^[3]

The 32 time slots of each subframe are assigned as follows:

Synchronisation preamble[edit]

This is a specially coded preamble that identify the subframe and its position within the audio block. They are not normal BMC-encoded data bits, although they do still have zero DC bias.

Three preambles are possible :

• X (or M) : 11100010₂ if previous time slot was 0, 00011101₂ if it was 1. (Equivalently, 10010011₂NRZI encoded.) Marks a word for channel A (left), other than at the start of an audio block.


• Y (or W) : 11100100₂ if previous time slot was 0, 00011011₂ if it was 1. (Equivalently, 10010110₂NRZI encoded.) Marks a word for channel B (right).


• Z (or B) : 11101000₂ if previous time slot was 0, 00010111₂ if it was 1. (Equivalently, 10011100₂NRZI encoded.) Marks a word for channel A (left) at the start of an audio block.

They are called X, Y, Z in the AES3 standard; and M, W, B in IEC 958 (an AES extension).

The 8-bit preambles are transmitted in time allocated to the first four time slots of each subframe (time slots 0 to 3). Any of the three marks the beginning of a subframe. X or Z marks the beginning of a frame, and Z marks the beginning of an audio block.

 | 0 | 1 | 2 | 3 | | 0 | 1 | 2 | 3 | Time slots
 _____ _ _____ _
 / _____/ _/ _____/ _/ Preamble X
 _____ _ ___ ___
 / ___/ ___/ _____/ _/ Preamble Y
 _____ _ _ _____
 / _/ _____/ _____/ _/ Preamble Z
 ___ ___ ___ ___ 
 / ___/ ___/ ___/ ___/ All 0 bits BMC encoded
 _ _ _ _ _ _ _ _
 / _/ _/ _/ _/ _/ _/ _/ _/ All 1 bits BMC encoded
 
 | 0 | 1 | 2 | 3 | | 0 | 1 | 2 | 3 | Time slots

In two-channel AES3, the preambles form a pattern of ZYXYXYXY…, but it is straightforward to extend this structure to additional channels (more subframes per frame), each with a Y preamble, as is done in the MADI protocol.

Channel status word[edit]

As stated before there is one channel status bit in each subframe, making one 192 bit word for each channel in each block. This 192 bit word is usually presented as 192/8 = 24 bytes. The contents of the channel status word are completely different between the AES3 and S/PDIF standards, although they agree that the first channel status bit (byte 0 bit 0) distinguishes between the two. In the case of AES3, the standard describes in detail how the bits have to be used. Here is a summary of the channel status word:^[1]

• byte 0: basic control data: sample rate, compression, emphasis
  
  • bit 0: A value of 1 indicates this is AES3 channel status data. 0 indicates this is S/PDIF data.
  
  
  • bit 1: A value of 0 indicates this is linear audio PCM data. A value of 1 indicates other (usually non-audio) data.
  
  
  • bits 2–4: Indicates the type of signal preemphasis applied to the data. Generally set to 100₂ (none).
  
  
  • bit 5: A value of 0 indicates that the source is locked to some (unspecified) external time sync. A value of 1 indicates an unlocked source.
  
  
  • Bits 6–7: Sample rate. These bits are redundant when real-time audio is transmitted (the receiver can observe the sample rate directly), but are useful if AES3 data is recorded or otherwise stored. Options are unspecified, 48 kHz (the default), 44.1 kHz, and 32 kHz.
  
  


• byte 1: indicates if the audio stream is stereo, mono or some other combination.
  
  • bits 0–3: Indicates the relationship of the two channels; they might be unrelated audio data, a stereo pair, duplicated mono data, music and voice commentary, a stereo sum/difference code.
  
  
  • bits 4–7: Used to indicate the format of the user channel word.
  
  


• byte 2: audio word length
  
  • bits 0–2: Aux bits usage. This indicates how the aux bits (time slots 4–7) are used. Generally set to 000₂ (unused) or 001₂ (used for 24-bit audio data).
  
  
  • bits 3–5: Word length. Specifies the sample size, relative to the 20- or 24-bit maximum. Can specify 0, 1, 2 or 4 missing bits. Unused bits are filled with 0, but audio processing functions such as mixing will generally fill them in with valid data without changing the effective word length.
  
  
  • bits 6–7: Unused
  
  


• byte 3: used only for multichannel applications


• byte 4: Additional sample rate information.
  
  • bits 0–1: indicate the grade of the sample rate reference, per AES11.
  
  
  • bit 2: reserved
  
  
  • bits 3–6: Extended sample rate. This indicates other sample rates, not representable in byte 0 bits 6–7. Values are assigned for 24, 96, and 192 kHz, as well as 22.05, 88.2, and 176.4 kHz.
  
  
  • bit 7: This "sampling frequency scaling flag", if set, indicates that the sample rate is multiplied by 1/1.001 to match NTSC video frame rates.
  
  


• byte 5: reserved


• bytes 6–9: Four ASCII characters for indicating channel origin. Widely used in large studios.


• bytes 10–13: Four ASCII characters indicating channel destination, to control automatic switchers. Less often used.


• bytes 14–17: 32-bit sample address, incrementing block-to-block by 192 (because there are 192 frames per block). At 48 kHz, this wraps every 24h51m18.485333s.


• bytes 18–21: as above, but offset to indicate samples since midnight.^[4]


• byte 22: contains information about the reliability of the channel status word.
  
  • bits 0–3: reserved
  
  
  • bit 4: if set, bytes 0–5 (signal format) are unreliable.
  
  
  • bit 5: if set, bytes 6–13 (channel labels) are unreliable.
  
  
  • bit 6: if set, bytes 14–17 (sample address) are unreliable.
  
  
  • bit 7: if set, bytes 18–21 (timestamp) are unreliable.
  
  


• byte 23: CRC. This byte is used to detect corruption of the channel status word, as might be caused by switching mid-block. (Generator polynomial is x⁸+x⁴+x³+x²+1, preset to 1.)

Embedded timecode[edit]

SMPTE timecode timestamp data can be embedded within AES3 digital audio signals. It can be used for synchronization and for logging and identifying audio content. According to John Ratcliff's Timecode: A user's guide, it is embedded as a 32-bit binary word in bytes 18 to 21 of the channel status data.^[5]

See also[edit]

• ADAT Lightpipe


• AES-2id


• 
  MADI, an extension with many more channels.

References[edit]

Further reading[edit]

• European Broadcasting Union, Specification of the Digital Audio Interface (The AES/EBU interface) Tech 3250-E third edition (2004)


• 
  Watkinson, John (2001). The Art of Digital Audio Third Edition. Focal Press. ISBN 0-240-51587-0.
  


• 
  Watkinson, John (August 1989). "The AES/EBU Digital Audio Interface". UK Conference: AES/EBU Interface. EBU-02.
  


• 
  Emmett, John (1995). "Engineering Guidelines: The EBU/AES Digital Audio Interface" (PDF). EBU.
  


• AES-2id-2006: AES information document for digital audio engineering — Guidelines for the use of the AES3 interface. (Downloaded from the AES standards web site; see external links)


• 
  Mark Yonge (June–July 2005). "AES3 Channel Status Revisited" (PDF). Line Up (101): 20–22. Archived from the original (PDF) on 2015-05-01. Retrieved 2013-09-01.
  


• 
  "AES3 / AES-EBU channel status byte settings".
  

External links[edit]

• Download page for AES standards